Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - kk15501

Pages: [1] 2
1
HD200 / Re: Parting out HD200
« on: September 03, 2013, 03:51:14 PM »
I am in need of a camshaft but might be willing to buy the head unit on the engine if you start parting out the engine

2
HD200 / Re: WTB, Camshaft
« on: August 21, 2013, 03:40:03 PM »
Thanks for the lead scosqt

3
HD200 / Re: WTB, Camshaft
« on: August 21, 2013, 02:57:16 PM »
Checked ebay, can't find cam or Iceman3

4
HD125 / WTB, Camshaft
« on: August 21, 2013, 02:40:05 PM »
I am need of a camshaft, anyone upgraded their SYM and have the old one laying around? Any year from 2006-2010 will work, thanks.

kk

5
HD200 / WTB, Camshaft
« on: August 21, 2013, 02:39:39 PM »
I am need of a camshaft, anyone upgraded their SYM and have the old one laying around? Any year from 2006-2010 will work, thanks.

kk

6
HD200 / Re: $12.00 air filter
« on: August 07, 2013, 03:41:57 PM »
That is sweet! Do you recall the B&G filter number? Mite be even cheaper on StealBay.

7
HD125 / Re: Piston ring?
« on: August 06, 2013, 11:16:41 AM »
FYI... got rings from easyparts.nl

8
HD200 / Re: Flywheel, Timimg chain and cam gear
« on: August 06, 2013, 11:13:46 AM »
Update, number 1 and 3 have been solved, answer was to get my wife to view the flywheel, seems she has much better eyesight than I. lol

Still would like to know why the cam gear has a slot if anyone knows?

Thanks, kk

9
HD125 / Re: HD 125 tops out at 40mph???
« on: August 06, 2013, 11:11:55 AM »
ootscoot, thanks for all your help so far, really goes beyond and helps with what the manual lacks. Status update, replace the rings, piston and cylinder look great with no scoring. Now here is my issue....

1. After I finally got the timing chain on the mark at TDC on the flywheel, the engine stops at half a turn using the 10 mm on the timing cam bolt. I am thinking cam 180 degrees off? Piston is stopping on valves open when should be closed?

2. As I was trying to rotate the cam 180, the mounting flange for the gear came off the camshaft, there is an index mark on the mounting plate but not on the end of the camshaft. How can I make sure I press it in the right place or does it not matter?

10
HD200 / Flywheel, Timimg chain and cam gear
« on: August 05, 2013, 01:58:56 PM »
I just got done rebuilding the engine and have a few questions on timing...

1. As I turn the engine, I cannot make out the T mark in the keyhole on the flywheel, looks like there are two marks, is the T the first or second mark as I turn CW?

2. The cam gear has two bolt holes but one is slotted, what is the purpose of the slotted hole?

3. Is the any easy way to retime without removing the flywheel cover? The manual instructions can be vague.

Thanks all, KK

11
HD125 / Re: HD 125 tops out at 40mph???
« on: August 03, 2013, 12:52:00 PM »
Yes, there was quite a bit of blue smoke

12
HD125 / Piston ring?
« on: July 02, 2013, 05:25:56 PM »
Anyone have a source for piston rings here in the US? 2010 HD125, burning oil pretty bad.

13
HD125 / Re: Starter
« on: July 02, 2013, 02:57:22 PM »
If anyone is interested, I bought a starter for a GY6, cut off and welded the rear mount. Works like a charm

14
HD125 / Re: HD 125 tops out at 40mph???
« on: July 02, 2013, 12:58:49 PM »
And I wonder, if this was caused by the gas in the crankcase, will the rings go back to normal?

15
HD125 / Re: HD 125 tops out at 40mph???
« on: July 02, 2013, 12:54:17 PM »
I finally did a compression test, did not have a 10mm adapter. Max psi is 130, manual states should be 170ish. Bad rings? would this cause lack of top end speed? Thanks Oot for your help

Pages: [1] 2